Leave Your Message
Thin Device Cooling: Piezo Micro Fans and Micro Pump Liquid Cooling by BESTAR
Blog

Thin Device Cooling: Piezo Micro Fans and Micro Pump Liquid Cooling by BESTAR

2026-10-30

1.Introduction
2.Active Cooling Is Now Ready for Mass Production
3.Three Cooling Routes Compared
4.How to Choose: Four Key Checks for Narrow Space Cooling
5.BESTAR Thin Cooling Solutions
6.Why Choose BESTAR as a Cooling Partner
7.Summary

Active cooling for ultra thin devices is moving from lab samples to real products. Engineers now ask a new question. It is no longer "Can we cool a thin device actively?" It is "Which cooling route should we choose?"
This blog compares the main options. It also explains two thin cooling solutions from BESTAR: the piezoelectric fan and the micro pump liquid cooling module.

Active Cooling Is Now Ready for Mass Production
Three signs show that the market has changed.
First, a chip maker has announced mass production of solid state cooling chips. Devices that use them are expected to reach the market early next year. For a hardware team, this matters today. The cooling choice you make now decides how strong your product will be in one year. You must check size, drive needs and airflow layout early.
Second, an embedded device maker has launched a mini industrial PC with solid state active cooling. The whole machine is about 35% thinner and about 43% lighter. It still keeps high performance. This proves that active cooling without a classic fan can work in a real, small machine.
Third, piezoelectric ceramic micro fans are moving fast. They have no bearing and no spinning blade. A piezoelectric ceramic part bends at high frequency and moves the air. The whole fan is very thin. These fans have entered volume production and customer validation.
So the topic has changed. Active cooling is no longer about whether it can be done. It is about which route fits your product. A thinner device leaves less room for the cooler. Thickness, drive method and airflow all affect the result. How should a thermal or mechanical engineer decide?

Three Cooling Routes Compared
Legacy micro electromagnetic fans
These fans use a motor, a bearing and a set of blades. They are well known and easy to buy. But they have limits.
·The motor and bearing set a minimum thickness. They can't be much thinner.
·Moving parts wear out over with time.
·They can be noisy.
·Dust can get into the bearing and cause failure.
Chip level solid state cooling
These parts have no spinning blade. They are thin and modern. But they also have limits.
·They need a high frequency drive circuit.
·They need a special cavity design to work well.
·Cost is still high.
·The supply chain is still growing up, so choices are limited.
Piezoelectric active cooling
The route is based on piezoelectric ceramic to transport air or drive liquid. It fits very narrow spaces well.
·Very thin and light.
·No electromagnetic interference. Zero EMI.
·No bearing, so no mechanical wear.
·Low power use.
·Good cooling effect to hot areas.
The piezoelectric approach is most suitable for thin devices due to size, reliability and cost considerations.

How to Choose: Four Key Checks for Narrow Space Cooling
When considering suppliers these are the four checks you should use.
1. Z height and space envelope. 7A thin part that moves no air does not help. Check the full envelope, including the air inlet and outlet.
2. Drive method and power use. The drive waveform is critical in working with piezoelectric parts. Airflow and vibration frequency are determined by the waveform. Determine which drive circuit should be used, and determine how much power is required for the circuit and how easy the control loop is.
3. Reliability in real conditions. A cooler with no spinning part has no friction wear. This helps the lifetime, often measured as MTBF. Also check shock and vibration, and stability at high and low temperature.
4. System cost and supply readiness. Don't consider just the part price, look at the full bill of materials. Ask one simple question. Can the supplier deliver in volume today, or is it only a concept? Start of production, or SOP, should be real and dated.

BESTAR Thin Cooling Solutions
BESTAR has worked on piezoelectric films and piezoelectric devices for many years. Our COOLTIST thermal management team uses this base to build cooling parts for thin devices. Two product lines are described below.
Piezoelectric fan
The piezoelectric fan has an inverse piezoelectric effect. A piezoelectric material is an object that changes shape when it receives a voltage.
Here is how it works, step by step.
·We apply an alternating voltage at a set frequency to the piezoelectric drive unit.
·A piezoelectric ceramic sheet is bonded to a metal blade. Together they form a piezoelectric vibrator.
·When power is on, the ceramic bends back and forth very fast. It drives the metal blade to vibrate at high frequency. The vibration can reach 23 kHz or higher.
·The fast blade pulls in air and compresses it.
·The air then leaves through tiny holes or slits in a jet plate. This forms a focused, fast stream of air that goes in one direction.
·The fast air stream speeds up the air that sits on the surface of the hot part. It takes away heat that was generated by conduction and radiation.
Natural convection is dependent on the air's ability to move on its own.That is slow. The piezoelectric fan forces the air to move, so it swaps hot air for cool air much faster. The cooling power is far higher than natural convection.
Because there is no motor, no bearing and no spinning blade, the fan can be very thin. It makes no electromagnetic noise. It is a good fit for local hot spots in tight spaces.

Micro pump liquid cooling module
The micro pump liquid cooling module uses a thin liquid cooling film. The film is made of three PET layers.
·Top layer: a sealing barrier layer.
·Middle layer: a flow channel layer. Channels are cut out of the PET film.
·Bottom layer: a sealing barrier layer.
The channels are filled with a cooling liquid. A piezoelectric pump pushes the liquid around the channels. The liquid picks up heat from the hot part and carries it to a cooler area, where the heat is released.
This is an active liquid cooling part. It is very thin. The thickness can be customized. Current options are 0.2 mm, 0.25 mm and 0.35 mm.
This film suits devices where there is almost no room for a fan. It can also spread heat across a wider area, so it helps with uneven hot spots.
Where these products fit
Our micro fans and liquid cooling modules are made for very narrow cavities. Typical uses include:
·Tablets and ultra thin laptops
·Handheld gaming devices
·Smartphones
·Smart wearables
·Robot joints
The two products can also work together. The fan handles air flow cooling. The liquid film spreads and moves heat. Together they break the limits of classic electromagnetic cooling.

Why Choose BESTAR as a Cooling Partner
Volume production and validation. BESTAR runs automated production lines. Our products have passed many strict tests. We support stable, large volume delivery at SOP.
Full engineering support. Our FAE team helps from start to finish. We support thermal simulation with CFD. We tune the drive waveform. We help you improve the structure and the air path. You get one team for the whole job.
Supply chain safety and cost control. Global Tier 1 and OEM customers need a safe supply. BESTAR offers a strong cost position and can act as a second source. This lowers your supply risk.
High reliability. Our parts have no mechanical wear. They resist vibration. They stay stable at high and low temperature. This matches what thin modern hardware needs from active cooling.

Summary
The next generation of thin hardware depends on better cooling structures. Piezoelectric micro cooling is changing what is possible in small spaces. Thin fans move air without a motor. Thin liquid films move heat without a bulky pump.
Are you planning cooling for an ultra thin laptop, an AI handheld, a mini industrial PC or a smart device? Contact the BESTAR thermal management team today. Request the datasheets for our micro fans and liquid cooling modules. Ask for test samples. Or talk with our engineers about your cooling design.